Smoke detector selection is set by the height of the space, the air movement and the value of the contents. The wrong choice means either a late alarm or three false alarms a week.

Three technologies

CriterionPoint detectorBeam detectorAspirating
Operating principleOptical or ionisation, single pointTransmitter-receiver beamDraws air samples through a pipe network, measured by laser
StandardEN 54-7EN 54-12EN 54-20 (classes A, B, C)
Typical ceiling heightUp to 10–12 m10–25 mUnlimited (depends on pipe design)
CoverageAbout 60–80 m² per detector100 m length × 14 m widthUp to 100–200 m² per pipe
SensitivityStandardStandardVery high (down to 0.005 percent obs/m)
Early warningOnce smoke reaches the ceilingOnce smoke breaks the beamBefore visible smoke
Sensitivity to air movementHigh (dilution)ModerateLow (active draw)
Maintenance accessPhysical access to every detectorAccess to two end pointsCentral unit, accessible from floor level
Dirty or dusty environmentsHigh false alarm riskLens contamination is a problemManaged with filters
First costLowestModerateHigh
Maintenance costHigh (working at height)ModerateLow (from floor level)

Which technology in which space?

SpaceRecommendedReason
Office, hotel room, corridorPointLow ceiling, still air; the most economical
Shopping centre atriumBeamLarge volume, point detectors hard to reach
High-bay warehouseBeam or aspiratingCeilings above 12 m; irregular air in narrow aisles
Automated warehouse (ASRS)AspiratingNarrow aisles, robot access, need for very early warning
Data centre / data hallAspiratingHigh air change dilutes smoke; point detector spacing is reduced (NFPA 72 17.7.7.3.3) and air sampling is also considered
Under a raised floorAspiratingCable dense, hard to access, shallow volume
Cold storeAspirating (heated unit)Condensation disables point detectors
Historic building, museumAspiratingMinimal visual impact, pipework can be concealed
Dusty industrial productionAspirating (filtered) or heatFalse alarms are inevitable with point detectors

Data centre note: in halls with high airflow, smoke is diluted. NFPA 72-2022 17.7.7.3.3 requires point detector spacing to be reduced where airflow exceeds 7.5 air changes per hour; under Table 17.7.7.3.3.2 the area per detector is 23 m² (250 ft²) at 30 air changes per hour and 12 m² (125 ft²) at 60. The NFPA 2001 annex (A.9.2.1) recommends that air-sampling detectors also be considered in high airflow.

Design items in an aspirating system

  • Pipe balance: each hole must draw approximately equal flow. On a long pipe the hole diameters are graded upwards, calculated in software.
  • Transport time: the time from the furthest hole to the unit may not exceed 120 seconds under NFPA 72-2022 17.7.4.6.2.1.
  • Sensitivity class: Class A for very early warning (data centres), B moderate, C standard. The higher the class, the more false alarm management matters.
  • Filter maintenance: in a dusty environment the filter change interval shortens, and that belongs in the operating budget.
  • Staged alarms: Alert, Action, Fire 1 and Fire 2 thresholds are set separately. The first stage triggers human response and the last triggers suppression.

Field errors with beam detectors

  1. Structural movement. A steel roof expands with heat, the alignment between transmitter and receiver drifts and a fault alarm follows. Choose a product with automatic alignment.
  2. Obstruction in the beam path. A banner, light fitting or rack installed later breaks the beam. The beam route must be given to the operator in writing.
  3. The hot layer under the ceiling. In summer a hot layer forms under the ceiling and prevents smoke rising; the beam path must sit below that layer.

Turkish context

BYKHY Article 74 requires the fire detection system and its components to be manufactured, designed, installed and operated in accordance with TS EN 54. Article 75(5) requires detectors to be sited to TS EN 54-14, Article 75(4) requires heat, flame or other suitable detectors where smoke detection is unsuitable, and Article 77 requires the control panel to be located where staff are permanently present. In practice point detectors are standard in residential, office and hotel buildings; beam detectors in shopping centre atria and high-bay warehouses; and aspirating systems in data centres, archives, museums and automated warehouses.

Frequently Asked Questions

Why are aspirating systems preferred in a data centre?

In a data hall with high airflow, smoke is diluted. NFPA 72-2022 17.7.7.3.3 requires point detector spacing to be reduced where airflow exceeds 7.5 air changes per hour (Table 17.7.7.3.3.2: area per detector 23 m² at 30 air changes per hour and 12 m² at 60); the NFPA 2001 annex (A.9.2.1) recommends that air-sampling detectors also be considered.

Up to what ceiling height are beam detectors used?

Typically 10 to 25 m. Point detectors lose reliability above 10 to 12 m; in an aspirating system the height limit depends on the pipe design.

What is transport time in an aspirating system?

The time from the furthest sampling hole to the unit. NFPA 72-2022 17.7.4.6.2.1 limits it to 120 seconds. As the pipe lengthens, the hole diameters are graded upwards to keep the balance.

Which detector suits a dusty production space?

False alarms are inevitable with point detectors. A filtered aspirating system, or heat detection instead of smoke, is preferred.

SprinkCalc — Fire Sprinkler Design Across Three Standards

SprinkCalc covers hazard classification, design density and area, K-factor selection, water demand and hydraulic calculations for NFPA 13, FM Global and BS EN 12845 in a single iOS app, and exports a professional PDF report.

Download SprinkCalc on the App Store

MEP Calc — 110+ Engineering Calculators

MEP Calc bundles 110+ engineering modules in one iOS app: 21 fire calculations plus heating, cooling, HVAC, plumbing, steam and natural gas.

Download MEP Calc on the App Store
Standards & References

The EN 54 series (fire detection and alarm systems), in particular EN 54-7 (point smoke detectors), EN 54-12 (beam type) and EN 54-20 (aspirating). NFPA 72 National Fire Alarm and Signaling Code. BYKHY fire detection clauses. Values are for information only.