In large atriums — malls, hotel lobbies, transit stations — a fire quickly fills the space with smoke. Before sprinklers knock down the fire, smoke can cut off egress on lower levels. NFPA 92 smoke control keeps smoke above a set height to buy evacuation time. This post summarizes smoke-layer analysis, plume math, and ventilation design.
Why Smoke Kills
- Hot smoke rises, cools, descends
- CO, HCN, HCl kill via inhalation
- Visibility drops under 10 m; egress slows
- Panic → wrong direction
NFPA 92 goal: keep the smoke layer above head height during evacuation. For atriums NFPA 101 requires the interface to stay above the highest unprotected opening or 1.8 m above the highest egress floor open to the atrium, for 1.5 times the calculated egress time or 20 minutes, whichever is greater (NFPA 101-2024, 8.6.7).
Two Main Strategies
- Natural (smoke vents): Roof vents open; hot smoke rises by buoyancy. Simple and power-independent, but sensitive to wind.
- Mechanical exhaust: Large fans pull smoke out. More controlled but power-dependent.
Smoke Plume Calculation
Heat release rate (HRR) × plume geometry gives mass flow. Typical design fires:
- Retail (mall shop): 2-5 MW
- Hotel lobby: 1-2 MW
- Transit station: 5-10 MW
- Theater stage: 5-15 MW
NFPA 92 axisymmetric plume above the flame height: m = 0.071 × Qc^(1/3) × z^(5/3) + 0.0018 × Qc (m kg/s, Qc convective heat release rate kW, z m) (NFPA 92-2018, 5.5.1.1).
Smoke Layer Interface
Smoke accumulates overhead; its lower boundary is the smoke layer interface. The level at which it is held depends on the design objective; for atriums NFPA 101 requires the interface to stay above the highest unprotected opening or 1.8 m above the highest egress floor open to the atrium (8.6.7).
Exhaust flow must exceed plume flow so the layer rises. If not, layer descends and egress fills with smoke.
Make-Up Air
While smoke exhausts, make-up air must enter. Otherwise atrium goes negative and doors jam. Rules:
- Make-up air supplied below the smoke layer; where it could contact the plume, velocity max 1.02 m/s (200 ft/min) unless a higher velocity is supported by engineering analysis (NFPA 92-2018, 4.4.4.1.4)
- Make-up dampers auto-open
Smoke Control Commissioning
- Cold smoke test: Low-density aerosol or theater smoke simulation
- Hot smoke test: Controlled small fire with real heat release
- Smoke layer height measured via laser/thermal camera
- NFPA 92 acceptance testing measures fan flow, door opening force and pressure differences (8.4.5).
Turkey Perspective
BYKHY Article 24(5) mandates natural or mechanical smoke control in atriums. Execution varies — some new malls run hot smoke tests, while many other projects only verify damper operation. Systems without real performance data pass on paper, fail in fire.
Common Mistakes
- No make-up air: Negative pressure traps doors.
- Sprinkler plume effect ignored: Sprinklers cool and lower smoke; must be modeled.
- Undersized exhaust: the heat release rate of a steady design fire is based on available or developed test data (NFPA 92-2018, 5.2.3.1); about 5 MW (5,275 kW) is often cited for mercantile occupancies (A.5.2.1).
- No hot smoke test: Real performance unknown.
Conclusion
Atrium smoke control meets architecture with engineering. A grand glass dome is beautiful — but deadly in fire. NFPA 92 + hot smoke test + make-up air + sprinkler integration done right lets 1,000 people evacuate safely.

Atrium smoke calc in MEP Calc
Plume flow, exhaust fan sizing, make-up air calc, NFPA 92 commissioning schedule.
View on App Store
SprinkCalc — Fire Sprinkler Design Across Three Standards
SprinkCalc covers hazard classification, design density and area, K-factor selection, water demand and hydraulic calculations for NFPA 13, FM Global and BS EN 12845 in a single iOS app, and exports a professional PDF report. One of the few tools that unifies all three major fire protection standards.
Download SprinkCalc on the App StoreCore references: NFPA 92, NFPA 101. Original NFPA post: NFPA Today - Atrium Smoke.