Pre-action bridges wet and dry pipe. Pipes empty, sprinklers closed. Water enters the piping when the detection system operates; discharge happens only when a sprinkler also opens. Data centers, museums, archives can't tolerate accidental discharge — pre-action removes that fear. Here are the three variants step by step.
What Is Pre-Action?
Wet pipe: pipe full of water; sprinkler opens → instant discharge.
Dry pipe: pipe pressurized with air; valve opens → 15-60 s delay.
Pre-action: pipe empty + sprinkler closed. Two-stage activation via detection. False-discharge risk minimized.
Single Interlock
Only the detection system opens the valve (NFPA 13 8.3.2.1(1)); a sprinkler opening alone does not:
- Detector activates → pre-action valve opens → pipe fills (sprinkler still closed).
- Then if sprinkler opens, water discharges.
Pro: Near-normal operation; only detector false alarm can wet the floor.
Con: Detector false alarm + later sprinkler hit (forklift) = damage.
Double Interlock
Both detector and sprinkler required to open valve:
- Detector activates → signal to panel.
- Sprinkler opens → pipe pressure drops (pipe normally has supervisory air).
- Both signals present → valve opens.
Pro: Highest safety, minimal water damage.
Con: Two signals → longer delay, which depends on system size. NFPA 13 sets no specific delivery time up to 500 gal (1900 L); above that, water delivery to the test connection within 60 s (8.3.2.3.1.2), a water delivery calculation (8.3.2.3.1.3) or the Table 8.2.4.3.2 times (8.3.2.3.1.4) apply, and double interlock systems are not gridded (8.3.2.7.1) — weigh the delay carefully in high-challenge areas.
Non-Interlock (Dry-Pipe-Like)
Either the detection system or an operating sprinkler opens the valve (8.3.2.1(2)). Similar to dry pipe but with detection.
Which Where?
- Museum / archive: In compact collection storage, dry pipe and double interlock systems are not installed (NFPA 909-2017 9.12.24); NFPA 750 applies to water mist.
Design Details
- Design area: +30 percent for dry and preaction systems protecting storage (CMDA, NFPA 13 20.16.3) — not a pipe-size rule
- Supervised air pressure in double interlock (leak test)
Common Mistakes
- Double interlock for storage: NFPA 13 permits dry and preaction systems in storage only where freezing or special conditions exist (20.16.2) and enlarges the design area by 30 percent; the delay is critical.
- Missing air supervision: Sprinkler strike goes silent.
- Not drying after test: System restarted without low-point drain.
Conclusion
Pre-action is a preferred solution for water-sensitive spaces; the variant depends on the hazard and the requirements of the applicable standard. Picking the right variant balances protection and cost. Turkish data centers are moving quickly to pre-action.

MEP Calc — 110+ Engineering Calculators
MEP Calc bundles 110+ engineering modules in one iOS app: 21 fire calculations (sprinkler, fire pump, clean agent) plus heating, cooling, HVAC, plumbing, steam and natural gas. Download it on the App Store.
Download MEP Calc on the App Store
SprinkCalc — Fire Sprinkler Design Across Three Standards
SprinkCalc covers hazard classification, design density and area, K-factor selection, water demand and hydraulic calculations for NFPA 13, FM Global and BS EN 12845 in a single iOS app, and exports a professional PDF report. One of the few tools that unifies all three major fire protection standards.
Download SprinkCalc on the App StoreCore references: NFPA 13 Ch. 8, NFPA 72. Original NFPA post: NFPA Today - Pre-Action.