A standpipe is the vertical water-supply network feeding firefighter and occupant hose connections in tall buildings. It may share a water source with sprinklers, but its calculation method differs. NFPA 14 sets flow and pressure per outlet; our job is to prove the hydraulically most demanding outlet still meets the criteria. Step by step:
Flow Requirements
NFPA 14 minimum flow per outlet:
- Class I - 2.5 inch outlet: 250 gpm (15.8 L/s)
- Class II - 1.5 inch outlet: 100 gpm (6.3 L/s)
- Class III - both: 250 gpm per Class I rule
For Class I and III systems the hydraulically most remote standpipe is calculated at 500 gpm (1900 L/min; 250 gpm from each of the two topmost outlets); 250 gpm (950 L/min) is added for each additional standpipe in buildings not exceeding 80,000 ft² (7430 m²) per floor (where the floor area exceeds 80,000 ft² (7430 m²), the second standpipe is taken at 500 gpm (1900 L/min) and the third at 250 gpm (950 L/min) if the additional flow is required for a building not sprinklered throughout in accordance with NFPA 13; NFPA 14-2024 10.6.1.1.4 and 10.6.1.1.4.1), and the total system flow does not exceed 1000 gpm (3800 L/min) in buildings sprinklered throughout or 1250 gpm (4750 L/min) in buildings not sprinklered throughout. This 500 gpm matches the Class I minimum flow given in our standpipe requirements article.
Pressure Requirements
Minimum residual pressure per outlet:
- Class I: at least 100 psi (6.9 bar) at a 2.5 in. (65 mm) outlet (NFPA 14-2024, 10.2.6.1)
- Class II: at least 65 psi (4.5 bar) at a 1.5 in. (40 mm) outlet (10.2.6.1)
Maximum static pressure 175 psi (12 bar); above this a pressure regulating valve (PRV) is required.
Calculation Steps
- Identify the hydraulically most demanding outlet: Usually top floor + furthest corner.
- Calculate required pressure at that outlet: 100 psi residual + elevation loss + friction loss + appliance loss.
- Simultaneous flow: for Class I, two outlets are assumed to flow at the same time on the most remote standpipe; pick the two most critical.
- Pipe sizing: Hazen-Williams (C=120 for black and galvanized steel in wet standpipes, C=100 in dry standpipes; values per NFPA 13-2025 Table 28.2.4.8.1).
- Pump selection: the operating point where the system curve meets the pump curve must not lie beyond 150% of the pump's rated capacity.
PRV Placement
If static pressure at an outlet exceeds 175 psi:
- Install a pressure regulating valve (PRV) at the outlet.
- PRV must cap both residual and static pressure under 175 psi.
- Without a PRV the hose and couplings are overstressed.
Example: 30-Story Building
30 floors, 3 m each, Class I standpipe. Target residual at top: 100 psi.
- Elevation: 30 × 3 = 90 m × 1.42 psi/m = 128 psi
- Friction loss (est. inside riser): ≈ 50 psi
- Total pump discharge pressure: 100 + 128 + 50 = 278 psi
That is below the 400 psi (28 bar) limit in NFPA 14 (10.2.1), but hose connection limits on the lower floors may be exceeded. The number of zones depends on the 400 psi limit, component pressure ratings and fire department pumping capability (10.5), not on a floor count. FM DS 3-7 also caps a zone at 275 ft (85 m) vertically (2.2.2.5).
Common Design Mistakes
- Using 65 psi at a 2.5 in. outlet: That value applies only to 1.5 in. (40 mm) outlets; 2.5 in. (65 mm) outlets need at least 100 psi (6.9 bar) (NFPA 14-2024, 10.2.6.1).
- Underestimating friction loss: Check the loss by calculation on long risers.
- Choosing zones by floor count: NFPA 14 gives no floor limit; the decision rests on the pressure calculation (10.2.1, A.10.5).
- Forgetting the PRV: a listed pressure-regulating device is needed where static pressure at a hose connection exceeds 175 psi (12 bar) (10.2.4).
Conclusion
Standpipe calculation is firefighter-focused, unlike sprinkler calculation. The goal: when a firefighter opens a hose, reasonable pressure arrives. Zoning and PRVs are needed where the 400 psi system limit or the 175 psi hose connection limit would be exceeded; skip this check and the system works on paper, not on site.

MEP Calc — 110+ Engineering Calculators
MEP Calc bundles 110+ engineering modules in one iOS app: 21 fire calculations (sprinkler, fire pump, clean agent) plus heating, cooling, HVAC, plumbing, steam and natural gas. Download it on the App Store.
Download MEP Calc on the App Store
SprinkCalc — Fire Sprinkler Design Across Three Standards
SprinkCalc covers hazard classification, design density and area, K-factor selection, water demand and hydraulic calculations for NFPA 13, FM Global and BS EN 12845 in a single iOS app, and exports a professional PDF report. One of the few tools that unifies all three major fire protection standards.
Download SprinkCalc on the App StoreCore sources: NFPA 14-2024, FM DS 3-7, NFPA 13-2025.