Textile dyehouses work with flammable solvents such as ethanol, isopropanol and toluene. Spray booths, drying ovens and solvent storage fall under NFPA 33 (Spray Application Using Flammable or Combustible Materials) and NFPA 86. Solvent vapour rising from the fabric creates a Class I Div 1 hazardous area, meaning an explosive mixture is assumed to be present at any time. Projects need to address the three elements — booth, solvent and electrical — together; designing one well and neglecting another puts the whole facility at risk.
Spray Booth Design
- Ventilation performance: vapour concentration in the exhaust stream must not exceed 25% of the lower flammable limit (LFL) (NFPA 33 Section 7.2); air velocity alone is not an adequate measure (Annex B).
- Enclosure: noncombustible metal (single-skin sheet at least 1.2 mm, each sheet of double-skin at least 0.9 mm; Section 5.3.2); the item most often skipped in site-built booths.
- Filter bank: traps overspray; overspray collection filters are inspected daily and clogged filters are discarded and replaced (Section 10.4.1).
- Fan: spark-resistant type with non-ferrous blades.
- Interlock: a fan failure must stop spraying immediately.
Solvent LEL and Ventilation
- Ethanol lower explosive limit (LEL): 3.3% (33,000 ppm)
- Toluene LEL: 1.1% (11,000 ppm)
- Operating limit: no more than 25% of the LEL — beyond this the booth is no longer at a normal operating point.
- LEL detector: where exhaust air is recirculated, a local alarm and automatic shutdown of spraying are required if vapour exceeds 25% of the LEL (Section 7.5); the monitoring equipment must be listed.
Sprinklers and Portable Extinguishers
- Booth sprinklers: NFPA 13-2025 Annex A.4.3.4.2 lists flammable liquids spraying as an Extra Hazard Group 2 (EH2) example; per Table 19.2.3.1.1 that means 0.40 gpm/ft² (16.3 mm/min) over 2500 ft² (232 m²). K115 (K8.0) sprinklers are used on site.
- Exhaust duct sprinklers: installed on 3.7 m (12 ft) centres in horizontal exhaust ducts, the first no more than 1.7 m from the duct entrance, with one sprinkler at the top of each vertical riser (ducts 0.25 m to 3.7 m wide, Section 9.6.6).
- Portable extinguishers: provided and located in accordance with NFPA 10 (NFPA 33 Section 9.8).
- Dry chemical: automatic ABC protection for the booth — a line that operates even when no workers are present.
Class I Div 1 and Electrical
- Booth interior: Class I Div 1 (NFPA 70) — the most severe area.
- Within 915 mm (3 ft) of booth openings: Class I Div 2 (enclosed booth, Section 6.5.4); for an unenclosed spray area, within 6.1 m (20 ft) horizontally and 3.05 m (10 ft) vertically is Div 2 (Section 6.5.1).
- Lighting: explosion-proof LED.
- Static bonding: 1 megohm (10⁶ ohm) maximum resistance to ground (Section 6.7); most colleagues skip this measurement at commissioning.

Dyehouse ventilation with MEP Calc
MEP Calc sizes dyehouse booth airflow, LEL monitoring and makeup air per NFPA 33.
Download MEP Calc on the App Store
SprinkCalc — Fire Sprinkler Design Across Three Standards
SprinkCalc covers hazard classification, design density and area, K-factor selection, water demand and hydraulic calculations for NFPA 13, FM Global and BS EN 12845 in a single iOS app, and exports a professional PDF report. One of the few tools that unifies all three major fire protection standards.
Download SprinkCalc on the App StoreNFPA 33, NFPA 86, NFPA 70 Art 516, OSHA 29 CFR 1910.107, EPA VOC regulations. NFPA 33 Spray Application standard.