In leather plants the work does not end with the chrome bath: surface dyeing and finish coating lines bring in flammable solvents such as toluene, MIBK and ethyl acetate. Tanning is done with Cr(III), but the Cr(VI) fumes released during the process are an IARC Group 1 carcinogen — so fire and worker respiratory health are on the table at the same time. NFPA 34 (Dipping, Coating and Printing Processes) covers dipping and coating processes that use flammable or combustible liquids (1.1.1); processes using only noncombustible liquids are outside its scope (1.1.4), and it does not address toxicity or industrial hygiene (1.2.2). Here NFPA 34 governs the solvent paint and finish line.

Chrome Bath Risks

  • Cr(VI) toxicity: carcinogen (IARC Group 1); local exhaust is essential
  • pH 2-3: corrosive solution
  • Temperature 40-50°C: an overheated bath can release hydrogen (H2)
  • Electrostatic charge: the agitator creates a large surface; do not skip bonding and grounding, including temporary lines

NFPA 34 Dip Tank

  • Automatic cover: closes on fire detection and cuts off oxygen at the liquid surface
  • Overflow pipe: tanks over 570 L or 1 m² of liquid surface have a trapped overflow pipe of at least 75 mm diameter (NFPA 34 5.6).
  • Drainage: tanks over 1900 L have a bottom drain to empty the tank in a fire; tanks with automatic-closing covers per 9.5 are exempt (NFPA 34 5.7).

Ventilation and Exhaust

  • Chemical storage: NFPA 30 has no 12 ACH value; where Class I liquids are dispensed, mechanical ventilation must provide at least 0.3 m³/min per m² of floor and not less than 4 m³/min (NFPA 30 18.6.6).
  • Paint shop: the spray booth interior is Class I Div 1; solvent vapor accumulates, so equipment selection is critical
  • Local exhaust: capture fumes at the source with lip exhaust along the chrome tank
  • Make-up air: clean make-up air to replace the exhausted air, with the intake placed so exhaust air is not recirculated (NFPA 34 7.4)

Fire Protection

  • Dip tank: NFPA 34 9.2.1 requires one of a water spray, foam, CO2, dry chemical, gaseous, water mist or (conditionally) sprinkler system; CO2 is only one of these options.
  • Spray booth: NFPA 33 9.1.3 permits a sprinkler, foam-water sprinkler, CO2, dry chemical, gaseous agent or water mist system.
  • Solvent storage and process areas: flammable liquid storage is protected per NFPA 30. NFPA 13-2025 Annex A.4.3.4.2 lists solvent cleaning, flammable liquid spraying and varnish/paint dipping as Extra Hazard Group 2 examples, so the Ordinary Hazard Group 2 density (0.20 gpm/ft², 8.1 mm/min) is not sufficient there.
  • Oil paint room: NFPA 30 Class IIIA liquid classification; observe storage limits
  • Portable extinguisher: one 6 kg ABC unit per 15 m of travel distance

Tannery ventilation with MEP Calc

MEP Calc sizes ventilation, local exhaust and make-up air for tannery chrome and solvent areas.

Download MEP Calc on the App Store

SprinkCalc — Fire Sprinkler Design Across Three Standards

SprinkCalc covers hazard classification, design density and area, K-factor selection, water demand and hydraulic calculations for NFPA 13, FM Global and BS EN 12845 in a single iOS app, and exports a professional PDF report. One of the few tools that unifies all three major fire protection standards.

Download SprinkCalc on the App Store
Sources & Further Reading

NFPA 34, NFPA 33, NFPA 30, OSHA 29 CFR 1910.1026, IARC Monographs Cr(VI). NFPA 34 Dipping and Coating.