In combined-cycle plants the lube and hydraulic oil system feeding the gas and steam turbine bearings holds 10,000-25,000 litres of mineral oil. ISO VG 32/46 oil, with an autoignition temperature of about 320 °C, sprays out as a jet fire if a line operating at 15-20 bar leaks. On site this risk is described as "the plant's quietest big hazard"; nobody notices the oil until it finds the hot turbine casing. NFPA 850 (Electric Generating Plants) is the main standard defining the water spray and CO₂ protection logic for lube oil reservoirs, oil pumps and bearing pedestals.

Oil System Risk Points

  • Main reservoir: 15,000-25,000 L stainless steel tank, typically located at basement level of the turbine building.
  • AC/DC oil pump: a seal failure creates a direct jet fire risk; even with two pumps in parallel, a single leak is enough.
  • Bearing pedestal: leaking oil ignites the moment it reaches the hot turbine casing; the most critical area met on projects.
  • Oil cooler: a leaking gasket in the plate heat exchanger spreads oil into the mechanical room.
  • Hydraulic system: phosphate ester fluid (Skydrol) at 200-300 bar has a higher ignition temperature than mineral oil, but the high pressure makes any leak spray more violently.

Water Spray Design (NFPA 15)

  • Density: 10.2 L/min/m² (0.25 gpm/ft²) for turbine bearings and hydraulic or oil-filled equipment; 12.2 L/min/m² (0.30 gpm/ft²) for the lubricating oil reservoir and lines beneath the operating floor (NFPA 850, 10.3.3.1.1, 9.6.1.2, 10.3.1.4.2). NFPA 15 7.3.3 calls for 12.2 L/min/m² on flammable liquid pool fires.
  • Area: over the oil-containing equipment and 6.1 m (20 ft) beyond it in all directions (NFPA 850, 9.6.1.2).
  • Water reserve: the water supply for the permanent fire protection installation is based on a 2-hour supply (NFPA 850, 7.2.1).

CO₂ Total Flooding

  • NFPA 12: total flooding CO₂ designed for surface fires is applied to the bearing enclosure.
  • Design concentration: 34% (for mineral oil).
  • Discharge time: for surface fires the design concentration is achieved within 1 minute (NFPA 12, 5.5.2.1).
  • Interlocks: pre-discharge alarm and a time delay long enough for evacuation (NFPA 12, 4.5.6.2.2), HVAC dampers close.
  • Drawback: CO₂ is an asphyxiant; where people may be present, an evacuation scenario and escape lighting must be planned.

Emergency Shutdown

  • Oil pump ESD: the shutdown signal reaches the pump within 5 seconds of detection.
  • Dump valve: oil is drained from the bottom of the main reservoir to an underground emergency tank.
  • Turbine trip: the burner management system (BMS) cuts the fuel.
  • Ventilation shutdown: dampers close, preventing smoke and oil vapour from spreading through the building.

MEP Calc — 110+ Engineering Calculators

MEP Calc bundles 110+ engineering modules in one iOS app: 21 fire calculations (sprinkler, fire pump, clean agent) plus heating, cooling, HVAC, plumbing, steam and natural gas. Download it on the App Store.

Download MEP Calc on the App Store

SprinkCalc — Fire Sprinkler Design Across Three Standards

SprinkCalc covers hazard classification, design density and area, K-factor selection, water demand and hydraulic calculations for NFPA 13, FM Global and BS EN 12845 in a single iOS app, and exports a professional PDF report. One of the few tools that unifies all three major fire protection standards.

Download SprinkCalc on the App Store
Sources & Further Reading

NFPA 850, NFPA 15, NFPA 12, FM Global DS 7-101, IEEE 979. NFPA 850 Electric Generating Plants.